Like an air conditioner, a swamp cooler thermostat automatically turns the cooling system on and off according to the temperature. You can adjust the temperature of your swamp cooler using its digital thermostat.
What Is A Swamp Cooler Thermostat:
You can control the temperature, fan, and pump speed with a swamp cooler thermostat. The thermostat allows you to monitor and change the temperature remotely. If it is too hot outside, you can turn on the pump and wait for the pads, and if it is too cold, you can turn off the pump.
Temperatures can be adjusted anywhere you want with digital thermostats. Your cooler will run automatically until it reaches the temperature you set on the thermostat. The cooler thermostat keeps the temperature in your desired range when the temperature reaches it.
How To Install A Thermostat On An Evaporative Swamp Cooler:
The first and most important thing when installing the thermostat in your swamp cooler is to choose a suitable location. Make sure you find a place that is not hot, ventilated or directly exposed to the sun. You should install the thermostat at the height of 4-5 feet.
Connect the standard connection of the fan and pump to the neutral supply if you are installing at 120V. If you do something wrong, it might have caused some serious trouble for you. If you do not know how to do this, you should call the professionals because this is a technical step.
[rank_math_rich_snippet id=”s-ea931be2-7970-4bbe-800a-40c5ddb77c54″]
The wiring should be run 6 inches from the wall at the outlet box, and then the wires should be connected to the thermostat. You should then clean up the wiring and ease the thermostat control into the outlet box. The thermostat control should be screwed into the outlet box, and a faceplate should be attached.
You can follow the given guide while installing the thermostat on the Evaporative cooler:
- Shut down the unit and look for the current controller.
- Record what each wire controls by taking pictures and writing them down.
- Install the new thermostat by preparing the wires
- Find the location of the switch, which is usually the old manual switch.
- Install the new thermostat by following the wiring schematic.
- Connect the new controller.
- Test the new controller by turning the power back on.
How To Wire A Thermostat To A Swamp Cooler:
Wiring a swamp cooler controller requires an understanding of what each wire controls.
Each wire controls a different function, such as the water pump or the fan motor.
If you are replacing an old controller, take a photo and write down the old connection so you can refer to it later.
Each wire can alternatively be traced to the inside of the cooler to determine its function.
Honeywell Swamp Cooler Thermostat:
In both honeywell swamp coolers and swamp coolers, the thermostat is the same. In terms of installation and operation, it functions similarly to a swamp cooler. Those familiar with the thermostat swamp cooler can see that it’s the same as the honeywell swamp cooler.
Evaporative Swamp Cooler Thermostat Wiring
If you have some electrical experience, you can easily wire a new thermostat to the swamp cooler.
If you do not have previous wiring experience, you should hire a professional.
It is necessary to wire in the fan motor and the water pump on all swamp coolers.
Some coolers come with an additional speed fan with high and low settings.
A motor would have two wires, one for high and one for low, plus a hot wire.
Whenever you are working on an evaporative cooler, make sure the power has been turned off at the breaker.
What Are The Benefits Of Installing A Swamp Cooler Thermostat?
Increased Comfort:
Having a thermostat for your swamp cooler makes the temperature easy to control. Cooler settings can be changed immediately rather than waiting till you feel uncomfortable. You can choose what temperature suits you best.
Timed Delay:
To use a traditional controller, you have to turn on the pump and soak the swamp cooler pads before running the fan. For the first few minutes after turning on the cooler, hot air will flow into the house if you skip this step. You can fix this with the thermostat. When the pads are soaked, the fan automatically kicks on after some time, usually two to five minutes. It no longer needs to be considered.
Timer Settings:
In most cases, swamp cooler thermostats come with a timer. You can set the cooler to run for two, four, or six hours with this feature. You can turn the cooler to turn off after a few hours of sleep, for instance, if you don’t want it running all night. There won’t be any need to get up and turn it off since it’s freezing.
Manual Settings:
If you wish, a swamp cooler can still be controlled manually. It is still possible to operate it manually.
Conclusion:
With the other beneficial and unique features, the swamp cooler has a digital thermostat function. With the help of a digital thermostat you can easily control the temperature and speed of a swamp cooler. If you feel cold after the swamp cooler has been running for thirty minutes, you can use the thermostat to reduce the speed or cooling.